gears

So while taking my XSC apart to switch everything over to a new chassis I noticed the clutch Bell gear is on an aluminum square block, with 2 set screws.....what a waist of human brain design. I don't know if it was when the car crashed at full speed that it made such a jolt or if its the power...

OK, so tonight I am going to take the belt drive from my XT and put it on the MT. My question is this- Does it benefit me to take the gears from the MT and put them on something else? Do they all have different ratios and gearing? Can someone smart suggest something until I can afford belt...

Running 4 pin now and gears are getting pin hole oval. I want to know if I square will have better gear options and will they be stronger?

I was running the other day and heard a noise then all the sudden the truck stopped, gear stipped through the gear case. I cut the gear case off so I could see all gears. I tightened everything and nut came off again. So tightened everything more (seemed too tight) but truck ran good and nut...

I can't find any made from steel out there. I need 10T and 11T

I know these are hard to find and I don't plan on ever using gears again. I will sell these for $40 shipped. New condition. - SOLD THX!

What are the Redcat part numbers for taller gears on an MT v3. My MT has the 4 pin hubs on the gear mount, stock its 25/35 gears. I was interested in more top speed till that mysterious 2 speed comes out;) Any info would be appriciated...

Looking at picking one of these up..(Redcat Rampage MTV3) http://www.davesmotors.com/s.nl/c.885035/n.1/it.A/id.8133/.f * Does it come with metal tranny gears? * What do I need to upgrade before I run to make it reliable? Thanks in advance

Are than any taller gears for the xb on the market? If so what do u guys suggest for running a big oval? Thanks

Hi guys, would like to purchase 51004 & 51005 steel gears, but don't know if these gears are the four pin or square shaft type. Thanks in advance Coleman

im having a hard time finding differ gears for my transmission on my mt. im wanting to put taller gears in it. it has 29/31/25/24 now. thinking around 31/29/25/25 would be nice. thanks

I just pulled my front diff apart and found only 2 planetry gears inside, the shaft that they sit on has a cutout and the case has a cut out as well for a second set of gears, I believe it should have 4 planetry gears in there. Can anyone confirm that this is the case. :confused:

I got a used dr a couple weeks ago. I was bashing around today and all the sudden the car acted like it went into nuetral. So took the gear cover off and two of the plastic gears were eaten alive. I didn't know these cars came with plastic gears? I've been looking around and I would like the...

Plan on rebuilding my gear plate and gears from scratch. Can anyone point me in the direction of some better directions? The manual directions are too small for mY old eyes.

Hello everybody im back at the gear thing i got them all on the truck and now they seem to have a tight spot in the two outside gears 25t and 35t gears is this normal and the center shaft that holds the two gears i noticed you can't tighten that rite down i had to back the nut off a little so...

hi i am a new member here.anyway i just bought steal gears for my mt v3 i tried to install them and the square hexs they fit on are not fitting in the gears is this the way they are do i have to dremel them to fit any info would be great thank you all

I have tried until my ears bleed why wont these gears line up?

Redcat has finally has the 4 pins gears and hardware in stock!!!!! just to let everybody know who has been looking for some. Just go under part serach for the D/R or the MT and the will come up.

Would like to switch to the 27/33 gearing on my mt now that I have the bow ties ....can someone give me a link on where to purchase these...and I want steel ones if that is at all possible

Hey i just wanted to share for those who are low on funds... So if you wanna get a bit more speed out of your Xt you can bring the gearing up by switching (A)29t and (B)31t ! Use the 31t in the (A) spot and 29t in the (B). This will give you a noticable kick in speed..just wanted to share this...