gears

I have mt and stripped the gears I am putting new ones on I have square drive gears but don't know which go where I know the 35 tooth but I have three 25 tooth one is flush where square is on back of gear and the other 2 have the square sticking out of gear.my question is where does the flush...

ten minutes into my brand new xb I hear chunking and clicking on deacceleration. Whenever it almost gets to a stop the driveline locks up. Off comes the plastic gear cover and out falls pieces. 10 minutes of 1/4 throttle break in !!!! I ordered a aluminum gear plate,bearings and new gears but...

Do the Chimera's only have 1 set of spider gears in the diff? When replacing mystery grease with some 7k and 5k fluid each diff only had 2 spider gears, not 4. Also looking at the manual it looks like there should of been some washers underneath the cup gear over the o-rings. I had the o-rings...

I was wondering if i should put gear lube on the gears that are on the side of the gears plate or i should leave it.

I was wondering if I run a 31/29/26/24 how much difference is it from 31/29/25/25

Going to do a rebuild soon, so as the title says... Was wondering if the Leopard 5692 on 6s will pull 10/44 gearing. Ol Fart makes a 44 and 48 in Delrin, currently I run 11/48 but have a 10... Would think 10/46 would work well but not sure about a 44 spur. Any input appreciated

I am looking for a set of used 24/26 gears to see if I like them over the 25/25....Thanks!

Hi Guys!, I'm new, but I had been reading the forums for a couple of months now and I decided to buy a Chimera with the aluminium gear plate (knowing this weakness) I was a little worried because I noticed a small gap between the main gears (first image), so I assume this was normal, but...

Hello I have two TT-5 buggies, well hopped up. On one I have the aluminium gear plate and pin gears. Running 35-25-25-25 no probs with 813 carb, pipe and porting work. Absolutely flies. On the other I decided to fit the 54090 gears and retain the plastic plate. Running 31-29-26-24. 813...

Hi Guys I took my gears out (metal pin type) and am not sure if I've got them right. I know the big one is right as the outside centre but not sure about the others. Does anyone know which one goes where? Thanks Phill

are 50067 and 50067N the same gears,,, one is for older v1/v2,, other is for the newer v3...,,, aren't the gears the same for the diffs,,,, finding different prices for each online..

Hello all, Did anyone here did the complete belt drive upgrade, I need all of the stuff that you replaced with the belt system. I need the gears the post for the gears and the gear cover. Please let me send me a pic and your asking price. Thanks

nice video of more top end on a simple stock gear switch hope you enjoy

Just got a MT Pro from Davesmotors. To the point: awesome, it has the four metal gears I assume is V4. Anyhow, great. However, It is already arranged 25T, 35T, 25T, 25T. Id like to stick with metal gear drive but really want it slower with higher torque. Hoping for 25-50% slower if...

So I'm running my Mt today and its sluggish off the jump. So I was kinda annoyed I have to tune on it, but it dawned on me.....it is ALOT slower than my xsc. They're both gear driven. But the mt with the tgn pipe just tops out fast and that's it..it may be slower than my traxxas summit. So I...

So I was unhappy with the clunky sound of my my while rolling it when it was off..so I pulled the cover and it was full of grime. Cleaned that and inspected the gears. All of them look perfect, so I pulled them to make sure all the shafts were tight, all perfect..so I put everything back...

whats up all im looking for a little more top end out of my xb does anyone know what the stock gears are (tooth count)? and if so what would be a good change to get more speed?

My Dune Runner V3 has the 4 pin gears, has anyone used this with a High Torque engine build. Can I stay stock or go with the square nut gears, possibly a belt drive. I just want a realistic appraisal, pro and con, preferably first hand experience.

Hi I am looking for metal gears. 31-29 teeth gears. From what I have gathered redcat has discontinued the square drive gears. So if any one has any I would like to purchase them for you.

-------------------------------------------------------------------------------- Anyone that got the belt drive, I can't find one, so would you want to sell the stock gears?