gears

Hello All! I want to thank you in advance for taking a moment in reading on the issue that I'm having! I have a RedCat Rampage MT that once every few months I play with. Just recently, I successfully started the truck with a single pull and as usual gave it about three minutes to warm up...

The pinion gear connected to the clutch bell at the end has nut and washer but has come loose a couple times on me. How tight does this have to be because if you tighten all the way the drive train gets stiff abd wont turn. Any suggestions ?

Hello. I just got my rampage xt and I went outside yesterday to run the second tank. While running it around it decided to stop wanting to move. I let it cool down and took the gear cover off to see if I see an issue. I noticed the bell house spins and the nut that goes through the first gear...

Hey guys had anybody tried swapping the A B Gears? Is there more top end?

I have the dune runner v3. Looking to get the 2 speed transmission and could use some suggestions on gearing. I'd like some nice low end with plenty on the top end. Any help much appreciated.

I am having serious binding issues with the two gears in my center diff. Here is how it started. I noticed the center drive shaft drive cup going to the front diff was loose and lost a set screw. So I ordered after market cups with the stainless sleeves pressed on etc. I installed the new cups...

anybody know how to fix this problem, they were turning nicly before i swapped a new clutch... all i know is the drive gear & the idle gears are too tight together and don't know how to fix it :(

Hi there, 1 of my gear for the drivetrain is misaligned, anyone knows how to realign the gear? It's the gear that has the brakes on the other side...Thanks a bunch!

So I have grenaded my second set of stock gears from the transmission. Any suggestions on better gear sets or even a different type of stetup? I have seen the posts about belt drives from Demon RC but its not available anymore. the gears flung so hard that it actually put a hole in the...

Alright guys I just blew the pinion and crown gear out of v3 mt. They look to be pop metal and they are straight cut, question is I see there are helical cut steel gears available but they show straight cut for the Mt? Should I get the helical or straight cut gears? Rob you have any...

In theory and sticking to a single speed what could a TT powered by a ported G320 get up to? I've heard you can swap the first 2 gears around to get silly top end but at the expensive of bottom end torque? Something a G320 should cope with much better then the stock engine? Would 45mph+ be...

Ok, has anyone ever used any of the MCD gears? Do they fit? Just curious as they have many different options gearing wise than Redcat seems to. If there was one thing that I wish Redcat had was more gearing combinations.

Still trying to fix my rear diff, I noticed that the ring an pinion gears can be strait or helical style. Is the strait any better?

Anyone know where to find 36t and 24t square drive gears? Can't seem to find any.

Hi, new to the gas rc world...I have the xt and I just added a jetpro pipe and a obr 7.5 hp engine. I keep ripping my gears up. I have done this twice know. I can't figure out why this keep happening. Do you have any idea why this keep happening.

Hello, I purchased a new RAMPAGE XR RALLY GAS from my local hobby shop. I purchased it about two weeks ago. It took me almost 2 hours to finally start the car. When I finally started it I drove it for a minute and all of the transmission gears stripped out. :mad: :mad: After checking the...

So my gasoline chimera had an accident last fall.....broke both 31 and 29 steel gears, the diff cover, front shock tower and part of the roll cage. 2 week ago, I finally decided to fix it all. I turned the engine before doing any work, and it turned on right away.....although I could tell all...

My friend did this to his Dune Runner aka Bajer.

I ran my chimera sr, and the gears melted! Missing teeth etc. I was wondering where to buy some high performance gears that won't wear out so quick. Thanks

So I've had my DR for about 4 months now and I have stripped out both the front and back spur/crown gears, The back went out first so I just put the front diff on the back ( front was disconnected because of a broken dogbone) ran through about 5 tanks of gas and now there stripped again. Is...