rampage xb

Dose anyone know of 8s lipo's that fit under the stock XBE body?

I have had my tuned pipe crack and almost fall off right where the pipe and the flang are welded together. So i removed the pipe and the left over pieces. I want to know if I can buy a stock pipe and have it attach to the flang of the tuned pipe, or if I just have to get a whole new tuned pipe.

Ok I am am trying to take the flywheel and clutch housing off my stock motor to put on another good one I have, I have taken out all the screws but I cannot figure out how it comes apart any tips would be great, thanks.

So it begins, doug has my new 7075 Xl xbe chassis on it way, so I have been gathering all the hops in the mean time..... I will be replacing my old motor 1200kv Horracing with a new leopard 780kv 4 pole motor and running it with a 16s capable esc on 12s...more pic's to follow...

I have an HY 30cc Fuelie that will start up but will not run. I've ran 2 gallons through it, and i wasn't haveing problems until now. When it idles the RPM's will go up and down, and won't stay at a certain RPM. It will also die when it gets up to speed and I apply the brakes. It also has...

Well, here's some pics with the brace on and trimmed body. After seeing all the bent tower pics recently, I decided to install it. Did a crappy job and was off over a quarter of an inch trimming the body...oh well.

i ran my xb for a few minutes when it started hesitating and then suddenly stopped. the servos and engine worked fine, so i tried pushing it and discovered that all four wheels were locked. the car also gave off some smoke and a burning plastic smell a minute before this happened. i took the...

I've been thinking it's time for a pipe and I'm considering a Jetpro rear tuned pipe. I've seen some pictures and I'm wondering if it hangs below the chassis or is it just the angle of the pic? And a pic of my XB. Cheers

Going to make an electric rally on my new chassis. 8c with a 2028 type motor. This is what I have so far. For size comparison those tires are 6.7 dia. Standard layout with all the parts I make. I'll be testing a belt drive with this build too.

I have a Jetpro rear pipe, and was wondering where to get some of that silicone [?] high temp hose. I can get a new 3" length for replacement ... but was looking for a longer piece. Trying to do a muffler repair on a 4 wheeler. I tried a few auto shops with no luck. I can't find any 1"...

Hello, I need new diff mount set for my rampage xb. Which one should i buy? plastik, gun metal, or aliuminium blue? Is bearings same for all of them or in aliuminium blue they are bigger? Thank you a lot.

Having some issues with an XB it has been broke in , but after break in the motor don't seem to rev out like the other xbs . tried fine tuning carb but didnt help. Now it will barely run even after putting adjustments on carb back to factory settings. it starts right up if you put gas down carb...

Hi Folks, I've searched and searched for this, but can't find out the size of the grub screw that holds the pinion to the motor shaft. Can someone help please? 5x5, 6x6? I've managed to bugger the standard grub screw (no loctite, worked itself loose, got mangled by spur gear), so need a...

Got these from DGIracing.com (Redcat forum sponsor) they are heavier than stock, but that does not worry me in the slightest.......with my driving style:D Wicked!!!!

hi! Im have a redcat rampage xb and I buy a pipe of a mt. served for the model redcat xb. Anyone know is in that model. Are any of you who use it. Here in Argentina there are few parts. They know if you can bring some spare parts and since local parts. Thank you.. bye

Finally found the fitting for venting the gas tank. Thanks to all you guys for the info. I used the 10-32 pressure fitting by Du-Bro (see 1st pic) from my local hobby shop. The clear hose was from an aquarium used to pump air bubbles I had laying around the house. On the cap I used a 5/32"...

I want to build an on road XBE but I'm not finding a lot of body's avalible. Not too conserned about the wheel base. I know about the subaru rally body's but Is that it??

Looking for this Roller will pay on pay pal. Please private message me if you have one to sell.

Guys, can I get a smaller spur for RedCat Rampage XB-E? Probably 35-38T Spur? Thanks

I'm thinking of a DT1 filter, not sure if I should get double or tripple? Or any other recomendations?