• Welcome to RedcatRampageForum! Are you a Redcat fan? If so you're in luck as you've have arrived to the biggest and best RedcatRampage RC community.

    Come join our community and ask your questions, show off your Recat RCs and share your experience!

bearings

  1. I

    Bearing Kit From Uberrc.

    I own the Maverick Blackout (aka V3 Rampage MT) i was after a High performance Bearing kit for my Blackout like alot of rampage owner on here are too. So i contacted Mark at Uber rc here in the uk and Mark kindly went on a mission.. So as of next week a Full High Performace Bearing kit for the...
  2. Z

    Sealed Bearings VS Shielded Bearings

    Has anyone tried sealed bearings on their Rc vehicles? Was doing some research and it is said that the seal bearings will get hot due to the friction of the seal but it will do a much better job at keeping the fine dirt out.
  3. I

    Bearing Question. need help please.

    Hi, I own the maverick blackout AKA rampage V3. now i am on the case with getting some performance bearings here in the uk and i want some advice about the 2 x 22*10*7mm Part # 50068 for the rampage. the supplier i'm dealing with has got all of them apart from these 2 problem ones. now...
  4. G

    Bearings

    Hello everyone, I want a complete bearing kit for my V3 MT. Could you tell me where I can find. Thank you all.
  5. T

    Bearing kit?

    Does anybody make a full replacement bearing kit anymore, I believe Fast Eddy did at one time?
  6. racetruck

    need bearings for servo saver post

    I'am looking for bearings for my servo saver post who had these the bearing measure 7x10x3 mm :rolleyes:
  7. C

    To use new case and/or bearings or not ?!

    Hey guys - need some advice ! I was tearing down my engine to install my new 30.5 ported kit that I received from OBR , which included 2 bolts to remove flywheel (they were out of the puller) . I got the flywheel off , but poked 2 holes through the case ! OOPS ! I talked to Sean via e-mail and...
  8. J

    how is the dr v3 trans drive line and is it a full bearing car

    you guys know if the dr v3 is a full bearing car and hows the tranny and is the drive line durable?
  9. F

    4-Bolt Zenoah G240RC/G270RC Bearings

    Anyone know what Bearings I need to get for this crank case if so could you let me know with a link or something thx....Don
  10. P

    Bearing sizes?

    I need to replace the bearings on the clutch bell shaft. What size are they? I just don't want to have to tear it down and leave it in piece spread out everywhere til I get the new ones. The exploded parts diagram in my manual doesn't list any part numbers for the bearings. Thanks! Parker
  11. J

    bearing

    Well i think my crank bearing went when i pull it over it makes a sqeaking sound so what bearing do i need ? And do them zero drag seal work good? thanks jim
  12. T

    clutch bell/mounting bearing size

    Hi guys, what is the size or part number for the bearing that is immediately next to the clutch bell?
  13. M

    bearing failure inside front gearbox

    i noticed a grinding noise inside the gearbox like if there was a broken teeth and after looking closer i noticed a little play in the drive cup... and when i opened the gearbox this what i saw: hard to believe... the bearing was desintegrated... still trying to figure what happened!
  14. P

    Bearings

    What are the best bearings to buy for the gear plate? What are the best bearings to buy if I am going to replace all the bearings in the TT? Keep in mind price, don't really want to spend a fortune on them. Thanks for the help, my dumb ass lost a gear plate bearing! Thanks in advance for...
  15. B

    bearing sets

    where can i find a compleat set at
  16. R

    Team Fast Eddy Bearings

    What are the ABEC rating for the Team Fast Eddy Plate Bearing Kit and also the full set bearing kit? The Rampage Rally already comes with ABEC 5, so what are the rating for the Fast Eddy ones. Just a goggle and they stated ABEC 1 and up. So I'm speading money to down grade and go slower???
    • ryuken168
    • Thread
    • bearings fasteddybearings
    • Replies: 7
    • Forum: Hop-ups
  17. L

    New bearings and seals still trouble

    ok i replaced the bearings and seals and fired it up, and it starts fine and idles yee haw, but its short lived, i take it around the yard and come back to me and it stalls, ok i turn the idle up and try again same thing, it will sit there and idle all day but when i open it up and stop fast it...
  18. H

    Fast Eddy Wheel Bearings

    I am going to need wheel bearings soon. I want to upgrade to fast eddy. I cant find a part #. The redcat manual says 24 X 12 X 6 but I assume it means 12 X 24 X 6. If its 12x24x6 thats the same size as 5b which is fast eddy 1204. So is there a fast edddy wheel bearing for the Ramp?
  19. T

    Sloppy Bearings

    Hey guys I got the aluminum gear plate and the aluminum center diff mounts and the problem im having is that the bearings fit in the places they are suposed to go but they are real sloppy there is about a mm of play between the mount's and the bearings
  20. M

    extra drive pinion bearing

    I was replacing bracke sqaure ,and notist a spot fore another baring in the outer center diff caryer ,so i went threw my bearings i had off of my mutilater , and 1 of the layshaft bearings fit i the opisit side of the caiyer, no more shaft wabell .so now i have 2 bearings to suport the shaft ,
Top