Silent_chaos
Senior Member
- Messages
- 905
Soup guys! Happy new year
Trying to put a hard bashing XB. When I 1st got my XB (been 6 months), I gathered a lot of hop-ups.
Current parts installed on Car:
-Aluminum C-hubs
-Al. front and rear bearing holders
-Al. cage
-Al. shock towers
-Al. gear housing
-Al. front upper suspension
-Al. rear upper link
-Al. Steering rocker
-Universal Dogbones
-Green type Boca Bearings
-CPI Rear pipe (very loud)
-Triple protection Air Filter
-Wt-998 carb
-4x Rear Trenchers
-Savox SV 0236 MG HV steering servo
-Savox SV 1258tg throttle servo
-M11X Sanwa Transmitter with Killer RC kill switch
A month ago, I was having problems with the Diff gear housing (kept breaking). Being a stubborn picky guy. Decided to go all out.
New parts that will be installed:
-DGI Steering links
-DGI rear upper links
-4x FLM CVD
-HITEC HV 7954 Throttle servo
-7075RC front and rear Diff housing
-8000 rpm HPI clutch house and spring
-Lightened Flywheel
-Double mesh Fuel Filter, Fuel lines, snappy tank vent, brass fittings
-Killer RC 7.4 V 7200 Mah battery with splitter (lessens the load on the M11x Receiver)
-DDM Receiver Signal Filter (for better response)
-Fast eddy Bearings
-9500 rpm (optional DDM spring)
-Killer RC Super Stainless steel pull start (already installed)
-7075RC Black anodized Chassis (Not in the pic, Will Hopefully reach in my hands on January 16th)
I have put some pics to sum up the above. I will remove and strap down everything; literally start from scratch. I will upload some more pics if you are interested.
let me know what you think. Any suggestions for future improvement are welcomed. Cheers.
Trying to put a hard bashing XB. When I 1st got my XB (been 6 months), I gathered a lot of hop-ups.
Current parts installed on Car:
-Aluminum C-hubs
-Al. front and rear bearing holders
-Al. cage
-Al. shock towers
-Al. gear housing
-Al. front upper suspension
-Al. rear upper link
-Al. Steering rocker
-Universal Dogbones
-Green type Boca Bearings
-CPI Rear pipe (very loud)
-Triple protection Air Filter
-Wt-998 carb
-4x Rear Trenchers
-Savox SV 0236 MG HV steering servo
-Savox SV 1258tg throttle servo
-M11X Sanwa Transmitter with Killer RC kill switch
A month ago, I was having problems with the Diff gear housing (kept breaking). Being a stubborn picky guy. Decided to go all out.
New parts that will be installed:
-DGI Steering links
-DGI rear upper links
-4x FLM CVD
-HITEC HV 7954 Throttle servo
-7075RC front and rear Diff housing
-8000 rpm HPI clutch house and spring
-Lightened Flywheel
-Double mesh Fuel Filter, Fuel lines, snappy tank vent, brass fittings
-Killer RC 7.4 V 7200 Mah battery with splitter (lessens the load on the M11x Receiver)
-DDM Receiver Signal Filter (for better response)
-Fast eddy Bearings
-9500 rpm (optional DDM spring)
-Killer RC Super Stainless steel pull start (already installed)
-7075RC Black anodized Chassis (Not in the pic, Will Hopefully reach in my hands on January 16th)
I have put some pics to sum up the above. I will remove and strap down everything; literally start from scratch. I will upload some more pics if you are interested.
let me know what you think. Any suggestions for future improvement are welcomed. Cheers.
Last edited by a moderator: